Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Roof Replacement & Installation in Delray Beach: What to Know First
CGI roof replacement and installation in Delray Beach typically runs $1,800 to $4,600 for a standard residential roof, with most jobs completed in two to four days once materials arrive. We are an independent CGI service provider, which means we quote the job straight and register the warranty layers in writing before our truck leaves your driveway. This page is for CGI owners who want the work done right, not the cheap bid. Call (561) 940-2917 and a live person answers, day or night.
How CGI Products Fail - and How We Fix Them
After four decades working South Florida roofs, we know exactly where CGI systems give out first. Here are the five failure modes we see most in Delray Beach:
- CGI Sentinel 9500 membrane seam separation. The heat and salt air along A1A breaks down the adhesive bond at the lap seams faster than the membrane itself. Water works under the edge, then the deck rots quietly. We strip the failed seam, inspect the deck, and re-bond with a manufacturer-spec adhesive, then seal the seam edge. We do not patch over a separated seam and call it done.
- CGI StormMaster 800 flashing failures at parapet walls. Delray Beach homes built in the 1980s and 1990s often have parapet roofs with original flashing that was never rated for the wind uplift we get during hurricane season. The flashing peels back, and water runs straight into the wall cavity. We remove the old flashing, replace it with code-compliant material, and mechanically fasten it before sealing. A caulk bead alone will not hold in a Cat 2 storm.
- CGI Tuff-Rib panel fastener back-out. On metal roof systems, the rubber washers under the panel screws harden in the Florida sun and crack. Water follows the screw shank down into the deck. We replace every suspect fastener with a new gasketed screw, not just the ones that look loose. If the panel is dimpled from over-tightening, we replace the panel section.
- CGI FlatLine 500 drain clogging and ponding. Low-slope roofs in the Lake Ida area collect leaves and palm fronds all year. When the drains clog, water ponds and the membrane degrades three times faster. We clear the drains, check the slope, and tell you honestly if the roof needs a taper system or just a maintenance schedule.
- CGI Mod-Bit blistering from trapped moisture. Blisters mean moisture got into the felt layers during installation or from a slow leak. Popping them releases water but destroys the membrane. We cut out the blistered section, inspect the insulation below, and install a new membrane patch with the same material spec as the original.
Our CGI Roof Replacement & Installation Process
Every CGI roof job follows the same straight line. No surprises. No change-order games.
- 1
Call and talk to a person. You reach a live dispatcher who asks the right questions: roof age, leak location, any prior repairs. We schedule a visit at a time that works for you.
- 2
Inspection and measurement. A background-checked, uniformed technician walks the roof, photographs the damage, and measures the affected area twice. We check the deck condition, not just the membrane.
- 3
Parts decision on paper. We quote OEM CGI materials side by side with quality aftermarket options when they exist. You see the price difference and the warranty difference in writing before you choose.
- 4
Replacement or installation. We tear off the failed section, repair or replace the deck as needed, and install the new CGI system to manufacturer spec. We do not cut corners on fastener spacing or seam overlap.
- 5
Water test and walk-through. We test every seam and penetration, then walk the roof with you so you see the finished work.
- 6
Warranty registration before we leave. Both manufacturer warranty layers get registered in writing, with durations stated. If the pane is not true, the job is not done.
What CGI Roof Replacement & Installation Costs in Delray Beach
Here is what we see across Delray Beach CGI roofs, based on the scope of the job:
- Small membrane patch or seam repair: $350 to $800
- Flashing replacement at parapet or chimney: $500 to $1,200
- Partial roof replacement (under 500 sq ft): $1,800 to $3,200
- Full residential CGI roof replacement: $3,800 to $4,600 for a typical 1,500 to 2,000 sq ft home
- Deck repair or replacement (if rot found): $400 to $1,500 added, quoted in writing before we start
The honest variables are deck condition, access difficulty, and whether you choose OEM or aftermarket materials. We give you a written line-item quote before work starts, and the price does not move unless you approve a change in writing. Call (561) 940-2917 for a free estimate.
Why Delray Beach Homeowners Call TruePane Windows & Doors for CGI Work
We have served this community since 2008, and Dale Kessler grew up in Lake Ida, so when we say we know how a Delray Beach roof weathers, we mean it. Every CGI job is backed by our Done Right Promise and The Keystone Standard: both manufacturer warranty layers registered in writing before the truck leaves, no arguing, no fine print. Our technicians are background-checked, uniformed, and trained to work in your home the way they would work in their own mother’s. And when a CGI roof has a problem we can also quote comparable systems from PGT, CWS, ES Windows, and ECO Window Systems if replacement makes more sense than repair. We are not the cheapest bid. We are the last call you will need to make.
FAQs
No, not when the repair is done to manufacturer spec using OEM materials or approved equivalents. We document every repair and register the warranty layers in writing, so if CGI ever questions a claim, you have the paper trail. Call (561) 940-2917 and we will walk you through what your specific warranty covers.
Most residential CGI roof replacements take two to four days once materials are on site. Partial repairs are often done in a single visit. We schedule around the weather because installing a membrane in the rain is exactly how you get blisters and seam failures.
If the damage is localized and the deck is sound, repair makes sense. If you have multiple failing seams, blisters across the field, or the deck shows rot, replacement is the honest answer. We will show you the damage in person and quote both options on paper, no pressure either way.
Yes, for current CGI product lines. For discontinued series, we will find the closest match or discuss a full replacement if a patch would be visibly off. We quote what is actually available, not what a catalog said ten years ago.
Yes, when the scope requires it. Delray Beach code applies to structural roof work, and we pull the permit, schedule the inspection, and make sure the job passes before we consider it done. You will see the permit in writing before we start.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Delray Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.