PGT Door Installation Nationwide | TruePane Windows & Doors

PGT Door Installation: The Delray Beach Owner’s Guide

PGT door installation in Delray Beach typically runs $850 to $2,400 installed, depending on whether we’re hanging a new impact-rated door, replacing a complete frame assembly, or retrofitting hardware and weatherstripping into an existing opening. We stock PGT-compatible door parts on the truck and can usually complete the job in a single visit. Most Delray Beach homeowners call us after a door starts binding in the frame, the rollers on a PGT sliding door grind to a stop, or the weatherstripping tears away and daylight shows through the threshold.

Call (561) 940-2917

The salt air here works on door hardware the way it works on everything else. After ten or twelve years, PGT door installation components that looked fine on a mainland house start showing their age in Delray Beach. Roller assemblies corrode, hinge screws loosen in rusted tracks, and the vinyl or aluminum frame shifts just enough that the panel no longer seats square. You’re not imagining it. The door is telling you something.

We’re an independent installer, not affiliated with PGT. That matters because we can quote you OEM PGT components side by side with quality aftermarket equivalents and let you see the difference on paper before any work starts.

Key Takeaways

• PGT door installation in Delray Beach runs $850 to $2,400 installed, parts and labor included.
• We carry OEM PGT door parts and proven aftermarket equivalents on the service truck.
• Most Delray Beach PGT door problems are discovered between years 10 and 15 in the salt air.
• All work is covered by our Done Right Promise, and both warranty layers are registered in writing before we leave your driveway.

Which PGT Models This Applies To

PGT sells a few door families in South Florida: the ClassicVue Max, the WinGuard, and the PremierVue S2000 are the ones we see most often in Delray Beach homes. Each has its own roller assembly, its own hinge geometry, and its own weatherstripping profile. A WinGuard sliding door roller is not interchangeable with a ClassicVue Max roller, even when both panels are 36 inches wide. That’s the gotcha most often missed by someone guessing at the parts counter.

To identify what you have, look for the PGT label on the door edge or the top of the panel. It will list the series, the DP rating, and usually the manufacturing date. Write those down before you call anywhere. If the label has worn off or peeled away in the humidity, measure the thickness of the door panel itself, the width of the bottom track, and the distance between the roller assembly mounting holes on the door stile. We can match from those measurements, but the label makes it simpler and faster.

On the OEM versus aftermarket question: PGT OEM parts keep the door exactly as it left the factory, and on an impact-rated WinGuard panel, we recommend staying OEM because the part was tested as part of an impact assembly. On non-impact doors, a quality aftermarket roller or latch from Prime-Line or Caldwell can perform every bit as well and sometimes lasts longer in coastal air than the original. We carry both, and we’ll show you the difference in price and warranty on a written quote so you can decide with your eyes open.

Signs Your PGT Door Installation Is Failing

• The door lifts or drops when you turn the handle. That’s a hinge or roller assembly wearing out of round. You can compensate by lifting the handle for a while, but the underlying wear only gets worse. Eventually the panel scrapes the threshold or the top of the frame.
• You have to shoulder the door to get it to latch. The panel has shifted out of square, usually from a failed roller on a slider or a sagging hinge on a swing door. Every forced slam accelerates the wear on the strike plate and the latch hook.
• Light shows through the perimeter after the door is closed. Weatherstripping has collapsed or torn away, and the panel is no longer compressing it. In Delray Beach, that gap is also how humid air, salt spray, and the occasional driving rain get inside.
• The door rattles when the wind picks up. On impact-rated PGT doors, a rattle that wasn’t there before usually means the panel has lost its compression seal against the frame. That’s a sign the door installation has started to fail, even if the glass is still solid.
• The lock engages but won’t fully throw. Rust and grit have built up inside the mortise lock or the hook bolt alignment is off. Forcing the key can snap the cylinder or strip the internal gears, which turns a simple lock swap into a panel repair.

Any one of these issues can be the symptom or the cause of the next. That’s why we always inspect the full door assembly when we’re out, not just the part you called about. The job is not done until the panel seats true in the frame.

Replacement Cost & What’s Included

For a PGT door installation in Delray Beach, you’re looking at $850 to $1,100 for a hardware and roller retrofit on an existing panel, $1,300 to $1,800 for a new door slab installed into an existing frame, and $1,900 to $2,400 when the frame itself has to come out and a full impact-rated assembly goes back in. Those are installed prices, including parts, labor, carpentry, fastener replacement, and haul-away of the old materials.

What drives the range is mostly the condition of the rough opening. If the original door was installed out of level, which we see often in older Delray Beach homes, the frame has to be shimmed and re-flashed before the new panel goes in. That takes more time and more material. We’ll show you the line items on your quote before we start, so you know exactly what you’re paying for. If the pane is not true, the job is not done.

Every PGT door installation carries our Done Right Promise. If something isn’t right, we’ll make it right with no paperwork fights and no arguing. Not that we expect any. We’ve been serving Delray Beach and the surrounding communities since 2008, and Dale Kessler still reads every job note personally.

DIY or Call Us?

An owner with a screwdriver and patience can safely clean the bottom track on a PGT sliding door, inspect the weatherstripping for tears, and tighten loose hinge screws that still have solid wood behind them. We’ll tell you to do those checks yourself and save the service call.

Replacing a PGT roller assembly or re-hanging a swing door is a different matter. The panels are heavy. An impact-rated WinGuard panel can weigh over 120 pounds, and a panel that slips out of the frame while you’re under it will break more than your schedule. That’s not a scare line. It’s the reason we send two uniformed techs to every PGT door installation in Delray Beach, and it’s the reason background-checked, uniformed technicians do this work the way they’d do it in their own mother’s home.

If you’re not sure whether it’s a DIY job or not, call (561) 940-2917. A live person answers, and we’ll tell you honestly over the phone whether you should tighten a screw or schedule a repair.

FAQs