Andersen Sliding & Patio Doors Nationwide | TruePane Windows & Doors

Andersen Sliding & Patio Doors in Delray Beach: What to Know First

We provide independent Andersen sliding and patio door repair and replacement in Delray Beach, with most service calls completed in a single visit and straightforward pricing quoted before work begins. We are not affiliated with Andersen, but our technicians work on their sliding and patio door lines every week, from older Narroline and 400 Series units to current A-Series and E-Series systems. Repair work typically runs $180 to $520 depending on rollers, track condition, and panel count, while full replacements generally land between $2,800 and $7,400 installed. If you own an Andersen patio slider that binds, leaks, or has dropped on its rollers, call (561) 940-2917 and we’ll walk you through what’s happening.

Call (561) 940-2917

How Andersen Products Fail, and How We Fix Them

Andersen builds a well-engineered door, and after four decades in South Florida we can tell you exactly where the weak points are on their sliding and patio lines. Here’s what we see most often in Delray Beach homes:

• Roller assemblies on 400 Series sliders from the mid-2000s. The original adjustable steel roller carriages corrode in coastal air and seize inside the bottom rail, which makes the panel drag and eventually score the track. The panel gets heavy, the handle stops helping, and homeowners assume the door is done. It usually isn’t. We replace the carriage with a stainless steel assembly, re-set the panel height, and the door carries like it did when it was new.
• Spring-loaded tandem rollers on contemporary A-Series and multi-slide units. These ride on nylon bearings that take a beating in salt air. When one roller in the tandem fails, the panel cants slightly and starts shaving the track edge, which produces a grinding sound most owners describe as “sand in the door.” We replace both rollers in the tandem as a pair, because doing one leaves the panel out of balance and the new roller fails early.
• Weep holes and sill drains on all Andersen sliding patio doors. In Delray Beach’s rainy season, a clogged weep system sends water over the interior sill and under the flooring. This is the failure most often misdiagnosed as a “bad seal” by other crews. The fix is not caulking the sill shut, which is what we sometimes find done on previous repairs. The fix is clearing the drain channels, verifying slope on the sill, and checking that the weatherstrip is still directing water outward.
• Interlock stiles on two-panel and three-panel Narroline sliders. The interlock is the vertical seam where panels meet and seal. Over years of use, the aluminum interlock on older Andersen units bends or wears, which leaves a gap that lets in air, rain, and in July, the humidity you feel at the center of the door. We straighten or replace the interlock piece and re-align the panel so the seam closes tight again.
• Screen track and kick-lock hardware on Andersen patio doors with original screens. The screen roller kits on older 200 Series and Narroline units are plastic and snap at the axle after enough cycles. The kick lock at the bottom of the active panel also strips its screws in the frame over time. We stock replacement screen hardware for common Andersen configurations, and we’ll tell you honestly when a new screen costs less than rebuilding the old one.

Our Andersen Sliding & Patio Doors Process

Every Andersen call follows the same careful sequence, whether it is a patio slider adjustment or a full panel replacement:

1. 1
   We answer in person. A live person takes the call at (561) 940-2917 and asks what the door is doing, how long it’s been doing it, and whether water or air has entered. No callbacks, no voicemail tree.
2. 2
   We measure twice on site. Our technician removes the interior trim if needed, checks the rough opening, levels the sill, and notes what the panel is doing before touching anything. Every opening gets read twice.
3. 3
   We quote on paper. You see the line items: parts, labor, any threshold or trim work. No surprise additions halfway through. If the fix is a $30 roller kit and not a panel replacement, that is what we quote you.
4. 4
   We decide parts together. On Andersen units, we use OEM parts when the warranty is active or when the part is structural. For out-of-warranty rollers, guides, and hardware, we offer a quality aftermarket option that often outlasts the original in coastal air. You choose with full information.
5. 5
   We do the work and test the result. The door is adjusted, cycled twenty times or more, checked for plumb and smooth travel, and inspected for air movement around the weatherstrip. If it does not operate right, it is not done.
6. 6
   We register the warranty layers. Before the truck leaves the driveway, both manufacturer warranty layers are registered in writing with durations stated. Then we clean the track, vacuum the area, and review what was done with you.

What Andersen Sliding & Patio Doors Costs in Delray Beach

Here are the ranges we quote most often for Andersen sliding and patio door work in Delray Beach. The numbers are ranges because panel size, track condition, and hardware type all move the final price:

• Roller replacement (single panel): $180-$340
• Track cleaning, alignment, and panel adjustment: $120-$220
• Roller replacement for both panels plus track service: $290-$480
• Weatherstrip and seal replacement (full perimeter): $140-$290
• Screen roller and hardware rebuild: $80-$160
• Full replacement sliding patio door (Andersen or equivalent): $2,800-$7,400 depending on size, impact rating, and finish

What moves the price is panel count, whether the track has been scored by failed rollers, and whether we are dealing with a contemporary multi-slide or a straightforward two panel patio slider. We quote on paper, upfront, and the number on that quote is the number on the bill. Call (561) 940-2917 for a free estimate on your Andersen door.

Why Delray Beach Homeowners Call TruePane Windows & Doors for Andersen Work

We have been serving Delray Beach and the surrounding communities since 2008, and in that time we have earned a reputation for doing the job right on the first visit and standing behind every installation. Our lead glazier, Dale Kessler, grew up in Lake Ida and learned the trade from a father who spent thirty years repairing storefronts along Atlantic Avenue, so the humidity, the salt air, and the particular failure patterns of South Florida door hardware are not abstract to us. Every Andersen job carries the Done Right Promise and The Keystone Standard: both warranty layers registered in writing before we leave. We are also authorized installers for, PGT, and CGI, which means if a repair stops making sense for an older unit, we can show you alternatives on paper side by side with honest numbers, not a sales pitch.

FAQs