Therma-Tru Door Installation Nationwide | TruePane Windows & Doors

Therma-Tru Door Installation: The Delray Beach Owner’s Guide

Therma-Tru door installation in Delray Beach typically runs $450-$1,800 installed, depending on whether we’re setting a new pre-hung unit, replacing a slab, or rebuilding the rough opening around a failed frame. We stock Therma-Tru-compatible hinges, sweeps, threshold caps, weatherstripping, and multi-point lock components on our trucks, so most Delray Beach calls are resolved same-day. What brings most owners to this page is a door that suddenly won’t latch, a threshold that’s rotted through after a decade of salt air, or a frame that pulls away from the jamb every July when the humidity settles in.

Call (561) 940-2917

The honest picture: Therma-Tru builds a solid fiberglass door, but the hardware around it takes a beating in South Florida. Dale Kessler has been setting doors in Palm Beach County long enough to know the failure pattern before the homeowner finishes describing it. If it is not in writing, it is not a guarantee - it is a conversation. Here’s what you need to know before you spend a dollar.

Key Takeaways

• Installed Therma-Tru door work in Delray Beach runs $450-$1,800 depending on scope
• TruePane is an independent installer, not affiliated with Therma-Tru - but we install and service their full residential line
• Most Therma-Tru failures in our area are hardware and threshold issues, not the door slab itself
• Free estimates, written line-item pricing, and both warranty layers registered before we leave your driveway

Which Therma-Tru Models This Applies To

This covers the Therma-Tru Classic-Craft, Fiber-Classic, Smooth-Star, and Pulse series, along with their benchmark door lines. If you have a Therma-Tru door that’s between 6 and 25 years old, the odds are good we’ve seen your exact model on a Delray Beach job site this year. The compatibility gotcha most owners miss: your door’s hinge pattern and backset are tied to the slab’s manufacturing date. Therma-Tru shifted hardware prep specs over the years, so a lock that fits one Fiber-Classic won’t necessarily fit another made five years apart. We match by the sticker on the hinge edge of the slab - it carries the series, size, and manufacturing code.

On the OEM-versus-aftermarket question: for seals, sweeps, and weatherstripping, we use Therma-Tru OEM parts because the tolerances are specific and the aftermarket versions tend to bind in the Florida humidity. For hinges and multi-point lock components, we’ve found quality aftermarket hardware from the same manufacturers Therma-Tru sources privately, and we’ll tell you where the savings are real. We measure every opening twice before quoting anything, and we put the options on paper side by side so you see exactly what you’re buying. TruePane is an independent service provider - we’re not a Therma-Tru franchise and we don’t pretend to be. We just install more of their doors correctly than anyone else in the coastal corridor.

Signs Your Therma-Tru Door Installation Is Failing

• Door won’t latch or the deadbolt misses the strike plate. Your frame has shifted, usually from heat and moisture cycling. The fix is re-shimming and re-securing the jamb, not forcing a bigger strike plate hole - that’s the shortcut that eventually costs you a full frame replacement.
• Visible daylight or draft around the slab edges. The weatherstripping has compressed past its service life or the frame was set out of square. In Delray Beach, the salt air accelerates weatherstrip degradation - expect replacement every 5 to 8 years on an ocean-proximate home.
• Water staining at the bottom corners of the jamb or threshold. This is the classic Florida failure: the threshold cap gets compromised, water works under it, and the jamb wood begins to rot. If you catch it at the staining stage, we can usually save the frame. If the wood is soft to the touch, it’s a rebuild.
• Door drags or scuffs at the top corner opposite the hinges. The slab has sagged because the hinge screws stripped out or the jamb has shifted. We replace the screws with longer anchors into the jack studs and reset the door - a 20-minute fix if addressed early, a hinge-mortise repair if ignored for a year.
• You have to lift the door to close it. The slab and frame have fallen out of alignment, often because the original install used 1-inch screws into the framing instead of structural anchors. We regularly see this exact issue on contractor-grade Delray Beach installs from the early 2000s.

Replacement Cost & What’s Included

Here’s the honest price picture for Therma-Tru door installation work in Delray Beach, broken down by scope:

• Hardware replacement (hinges, sweep, weatherstripping, strike plate): $95-$295 including parts and labor
• Threshold cap or threshold replacement: $150-$425 depending on damage found underneath
• Frame repair and re-set (re-shim, re-anchor, re-plumb the jamb): $350-$800
• Slab replacement on an existing frame: $600-$1,200 depending on series and glass configuration
• Full pre-hung door replacement including new frame: $1,100-$1,800 for a standard 36×80 entry, higher for transom or sidelight configurations

Every quote includes line-item pricing so you see parts, labor, and disposal separately. The Keystone Standard means both manufacturer warranty layers are registered in writing with durations stated before our truck leaves your driveway, and the workmanship is covered by the Done Right Promise. No change orders, no surprise line items, no arguing. Call (561) 940-2917 for an exact quote - estimates are free and the person who answers will be a person.

DIY or Call Us?

You can safely inspect several things yourself: check whether the weatherstripping has flattened or torn, note where the door binds, and see if the threshold cap has started to separate from the base. That diagnostic information helps us quote accurately over the phone. What you should not do is attempt to remove the slab yourself to access the hinges - that’s a 60-to-120 pound fiberglass door with a glass insert, and when it comes off the hinges, it wants to go through the nearest window. We’ve been called to more than one DIY hinge repair where the door went sideways and the cost doubled. Dale Kessler spent nearly two decades learning every failure mode the South Florida climate can throw at a door before starting TruePane, and we’d rather see you spend that time fishing than fighting a sprung slab. Call (561) 940-2917 and we’ll send a background-checked, uniformed technician who measures twice and quotes on paper.

FAQs